The tool path mode and the feed mode in numerical control milling are introduced.
介绍了三轴数控铣削加工的走刀方式和进刀方式。
This paper introduces a number to control a different characteristics of tool path mode, and influenced parts of factors of its choice,and tally up a reasonable choice to walk the principle of tool path mode,pass to process a solid example to come to verify its possibility further.
介绍了走刀方式的不同特点,及影响其选择的部分因素,并总结合理选择走刀方式的原则,通过加工实例来进一步验证其可行性。
Taking NC macro program in spherical ring-cutting as example,the paper puts forward the convenience of NC macro program in programming for complicated components,and points that the design of feed route is critical in NC programming.
以环切法球面加工的数控宏程序编制为例,提出了在编制复杂零件的数控程序时采用宏程序的便利性,同时指出了走刀路线的设计是数控编程的关键。
In the process of drawing up the technology route of numerical- controlled machine toolsin processing parts,if limited to the Parts themselves,the feed route drawn up may not bethe shortest and it is possible that difficulties may arise in programming.
在制定数控机床加工工件的工艺路线时，如果仅局限于工件本身，制定出的走刀路线可能并非最短，并有可能造成编程麻烦，本文介绍了如何从数控机床实际具有G00路径、数控系统实际采用的插朴方法以及工件本身的几何形状特点三方面着手，综合分析制定实际最短走刀路线，以充分发挥数控机床的技术经济效益。
Research on the Optimization of Cutting Parameter in Single Pass End-milling for Numerical Control Milling Machine;
数控铣床一次走刀立铣切削用量优化的研究
Research on the Optimization of Cutting Parameter in Single Pass End-milling for Numerical Control Milling Machine;
数控铣床一次走刀立铣切削用量优化的研究
Oil the foil after cleaning the blades once a week.
动刀片每周一次涂油。
steel wire cutter one step quick forming
钢丝刀一次快速成形法
throw-away cups, tissues, razors
一次性杯子、 纸巾、剃刀.
Since he left, she's been sitting at home eating her heart out.
他走了以後, 她一直坐在家里, 心如刀割.
A soldier came up to her with a drawn saber.
一个士兵拔出马刀向她走来。
disposable towels and razors
一次性使用的毛巾和刮胡刀
disposable razors, nappies, syringes, plates
一次性的剃刀、 尿片、 注射器、 盘子.
But you must get there by a different way this time.
可这次你得另走一条路。
Sukey, take it off again. Sukey, take it off again.
茶水壶，再一次把它拿走。茶水壶，再一次把它拿走。
You go into the restaurant, then pick up a tray, knife fork and spoon.
你走进这样的餐馆，拿起一套托盘、刀叉和餐匙。
Now stalwart players have come up with a strategy - start with scissors.
现在，死忠玩家得出一套策略－第一次出剪刀。
It uses two-way cutlery device to finish noching the paperboard bag, color bag and ocatgonal bag simultaneously.
双向进刀，并列纵横向一次完成纸张开槽工序。
Usage: lubricate cutter before starting work, lubricate it every one hour.
使用方法：工作前润滑刀具，每个小时润滑一次。
Analysis of postoperative long-time effect of LASIK using disposable microkerotome
使用Moria 2一次性90刀头LASIK术后长期效果分析
One day, he came to see Dong Zhuo with a Borrowed Blade. The latter was sitting in his Bedroom, his Brave step-son Lu Bu standing by his side.
一日,曹操借王司徒宝刀一口,藏刀来到相府。他走到小阁,见董卓坐在床上,义子吕布侍立于侧。
Once again I was tempted. And once again I decided to stay on.
我又一次动心想走了。但是又一次我决定留下来。
Last time I went with a flourish trumpets, but now I want to go without any fuss at all.
上一次我走得声势浩大，可这次我要走得不出一点儿声响。