The shortcomings of the boss quill′s using previous hot extrusion process were analysed.
分析了汽车轮毂轴管原热挤压工艺存在的缺点与不足,并在分析研究轴管性能要求和结构特点的基础上,经过反复的分析、计算、试验,形成了能满足产品质量和大批量生产要求的复合热挤压新工艺。
The existing shortcomings of the previous hot extrusion process of the boss quill were introduced and the prominent characteristics of the improved process were pointed out.
介绍了轮毂轴管原热挤压工艺存在的缺点与不足 ,指出了改进工艺的突出特点。
Taking outer ring forging of the second-age hub bearing as an example,the simulation analysis is made.
以第二代轮毂轴承外圈锻造为例进行模拟分析,对预成形模型的实验和模拟结果作了对比,提出产生过大锻造力的一个原因是最终成形阶段工件在模腔内分布不均使变形速率急剧增加,提出了预成形坯的设计优化准则,依此设计的第二代轮毂轴承外圈的优化预成形结构、锻造力比传统设计下降了一半以上。
The crowning of the front hub bearings of Santana car is analyzed by using ANSYS finite element software,and the proper crowning form and optimal crowning match relation between roller and raceway are determined.
用ANSYS软件对桑塔纳轿车前轮毂轴承进行有限元分析 ,确定合理的凸度形式及滚子与滚道的最佳凸度匹配关系 ,给出了滚子、内圈滚道最佳凸度控制方程。
By using LGM-15/45 automobile hub bearing simulation tester, the simulation test at speed of 95 km/h for car has been made, the total test time is 720 hours.
介绍了LGM - 15 4 5汽车轮毂轴承模拟试验机 ,对富康轿车前轮毂轴承及桑塔纳轿车后轮毂轴承进行模拟试验。
Study and Application of Hot Extrusion Process for Boss Quill
汽车轮毂轴管复合热挤压工艺的研究与应用
Moment Rigidity Analysis on Flange of Automotive Hub Bearings
轿车轮毂轴承轮毂凸缘力矩刚性分析
SMALLER DIAMETER OF PIVOT BEARING
轮毂轴承的较小直径端
wheel hub bearing adjusting nut
车轮毂轴承调整螺母
Install rotor on axle hub.
在车轴轮毂上安装转子。
Hub And Bearing Assembly Mounting Surfaces
轮毂轴承组件固定面
Front Stub Axle To Hub Bearing Nut
前螺桩轴至轮毂轴承螺帽
"The wheels were made like carriage-wheels, the rods on which they were fixed, the parts forming their edges, their rods and the middle points of them, were all formed out of liquid metal."
轮的样式如同车轮。轴，辋，辐，毂都是铸的。
A slot for a key in the hub or shaft of a wheel.
键槽轮子的毂或轴里的键的沟槽
Shafts and hubs are usually fastened together by means of keys.
轴和轮毂通常用键固定在一起。
Analysis of the Calculation and the Modes of Break-down of Automobile Hub Bearing
汽车轮毂轴承的计算及失效形式分析
Contact analysis of MW wind turbine hub and bearing bolt connection
风力机轮毂和轴承螺栓联接接触分析
An enlarged part of a shaft to which another shaft is coupled or to which a wheel or gear is keyed.
轮毂一轴与另一轴耦合处或一轴与机轮或齿轮楔合处的增大部分
If the axle shaft and hub bearing are being removed in order to service another component, the axle shaft and hub bearing can be removed as an assembly.
如果维修时需拆卸主动轴和轮毂轴承，主动轴和轮毂轴承可作为一个总成加以拆卸。
The hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly.
更换轮毂及轴承组件内的车轮固定螺桩无需自转向关节中取出轮毂及轴承组件。
The Process Engineering and Numerical Simulation on Precision of Hub Unit Bearing;
轿车轮毂轴承单元精锻工艺设计及数值模拟
Study on Modeling Technique and Improving Reliability of Automobile Hub-Bearing
汽车轮毂轴承的可靠性建模与试验技术研究
Modeling & Numerical Simulation of Fatigue Life of Hub Bearing Based on Multi-Bench Test Load
轮毂轴承多工况疲劳寿命建模与数值仿真