This paper makes systematic reserch about the calculation of the assembling size chain formed by adjusting method with group spacers.
本文系统研究了用分组垫片法解装配尺寸链时的计算方法。
Analysis about pinion gear bearing shim measuring influence factors & optimization in re-checking scheme
主齿轴承垫片测选的机理分析及复测方案优化
Remove the depth shims from rear pinion bearing cup bore in axle housinRecord the thickness of the depth shims.
从轴管里的后小齿轮轴承盖孔拆卸限深垫片。记录限深垫片厚度。
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
shielded ball bearing
带防护垫圈的滚珠轴承
By measuring all dimensions associated with bearing, the shim dimension satisfying the requirements of bearing bore dimension was calculated to finally reach the requirements of assembly.
通过测量轴承各相关件的尺寸,计算出满足轴承内孔尺寸要求的垫片厚度,最终达到装配要求。
A bushing or similar lining for a bearing, made from a copper alloy.
铜套或铜衬垫用铜合金制的轴承轴瓦或套筒式衬垫
Bolt( screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.
螺栓（钉、帽、头螺栓、簧垫圈、、珠轴承、柱轴承）最常用的机械零件。
Plain bearings-Ring type thrust washers made from strip-Dimensions and tolerances
GB/T10446-1989滑动轴承整圆止推垫圈尺寸和公差
Plain bearings-Pressed bimetallic half thrust washers -Features and tolerances
GB/T10447-1989滑动轴承半圆止推垫圈要素和公差
Place 4 adapter blocks so they do not damage the bearing cag
安装4个接头垫块，以免损坏轴承弹子盘盖。
a alloy of tin with some copper and antimony; an anti-friction lining for bearings.
含锡和一些铜、锑的合金，用作轴承防摩擦衬垫。
Research Status and Prospect of Spherical Plain Bearings with Self-lubricating Fabric Liner
织物衬垫自润滑关节轴承的研究现状与展望
Provide non-standardized products：Cylindrical bushes, flanged bushes, thrust washers, flat strip material, half bearing, wear plate.
可供非标产品：直套、翻边轴套，止推垫片、板材、轴瓦、滑板。
The Application of a Single Chip Processor 8098 to Detecting the Axial Clearance of a Bearing
8098单片机在轴承轴向间隙检测中的应用
377 bolt (screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.
螺栓（螺钉、螺帽、双头螺栓、弹簧垫圈、销、滚珠轴承、滚柱轴承）是最常用的机械零件。
Research on Inner Rotor Type Disk Bearingless PM Motor;
内转子式片状无轴承永磁电机的研究
Finite Element Analysis of Bearing in Segment Erector System for TBM
TBM管片拼装系统轴承有限元分析
Research Progress on Tribological Properties of Self-lubricating Materials Liner for Spherical Bearings
自润滑关节轴承衬垫材料摩擦学性能的研究进展