The calculation results show that the most important factor of effecting the center movement of crankshaft is the acting direction of the bearing load.
计算结果表明,影响变负荷轴承轴心运动轨迹的最主要因素是轴承载荷的合力方向,以轴承平面内某一半径射线为基准,在整个工作循环中轴承载荷方向变化在此射线两侧±90°范围内时,轴心运动稳定;超出这一范围则轴心运动轨迹不稳定;其他影响因素的微小变化会导致轴心运动轨迹的剧烈变化。
Changing the sequence order of governing valves can decrease the bearing load.
选择合适的调节阀重叠度能够提高调节级效率;合理的开启顺序可以减轻轴承载荷。
Amplitude of steam turbine generator has relationship between bearing load and oil film stiffness.
根据转子动力学及润滑理论 ,对振幅与轴承载荷及油膜刚度之间的关系进行了分析 ,得到如下结论 :轴承载荷增加 ,油膜刚度增大 ,轴颈与轴瓦之间摩擦程度增加 ,振动幅值减小。
Study on Load Analysis Method for Diesel Engine Crankshaft Main Bearing Based on ADAMS;
基于ADMAS的柴油机曲轴主轴承载荷分析方法研究
STUDY OF THE LOAD ON THE JOURNAL BEARINGS OF THE TRICONE BIT BY THE METHOD OF ANALYSIS OF THE RANDOM PROCESS
用随机过程分析方法研究牙轮钻头轴承载荷
The Dynamic Characteristics Analysis for the Load-sensor in the Rotor-bearing System
转子系统轴承载荷传感器动态特性分析
Research on the Model of Blade Bearing Loads of the Wind Turbine
风力发电机桨叶轴承载荷分析模型的研究
The device is very facilitated to measure the load of oil film bearing on-line.
该装置有利于实现油膜轴承载荷特性的在线监测控制。
Load analysis of cylindrical roller bearing with inclined axis
圆柱滚子轴承轴线倾斜时的载荷分析
Deep groove ball bearings mainly take radial load as well as take moderate axial load.
深沟球轴承主要承受径向载荷，也可承受一定量的轴向载荷。
How do engineering materials deform when bearing mechanical loads?
如何做工程材料变形时，轴承机械载荷？
Axial load-deformation curve and preload on angular con act ball bearings
角接触球轴承的轴向载荷—变形曲线和预紧
Four pionts angle contact ball bearing is separable bearing,it can be subject to bi-directional load and have the function of both single row and double rows bearings.
四点接触球轴承为可分离型轴承，可承受双向轴向载荷，并有单列和双列角接触球轴承的功能。
Tapered roller bearings are generally used to support combined load mainly consisting of radial load.
圆锥滚子轴承主要用以承受以径向载荷为主的径向与轴向联合载荷。
Taper roller bearings are generally used to support combined load mainly consisting of radial load.
详细信息:圆锥滚子轴承主要用以承受径向载荷为主的径向与轴向联合载荷。
Load distribution analysis in a single row four-point-contact slewing ring
单排四点接触球转盘轴承的载荷分布分析
The Stress Analysis of Hub Bearing Based on Multi-bench Test Load
基于多工况台架试验载荷的轮毂轴承受力分析
A Study on Adiabatic Transient Behavior of Thrust Bearing under Dynamic Operating Load
载荷扰动下滑动推力轴承绝热瞬态过程分析
Calculation of Preload Coefficient of Matched Angular Contact Ball Bearing Sets
多联组配角接触球轴承的预载荷系数计算
Thermal Transient Behavior of Thrust Bearing under Step Applied Load
阶跃载荷扰动条件下推力轴承热瞬态过程研究
The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.
为了避免划伤，轴承上的最大负荷应该总是小于其卸载负荷。