Three dimensions CAD system used in spindle bearing of aircraft engine;
航空发动机主轴轴承三维CAD系统
This paper discusses the working condition of machine tool's spindle bearing can be distinguished by bearing's vibration signal.
论文阐述了利用轴承振动信号可判断机床主轴轴承的工作状态,通过频谱分析可对轴承进行故障诊断及预紧力确定;应用B&K2148采集振动信号,MATLAB进行数据处理,对CKS6116型机床主轴前轴承进行了故障诊断与预紧力分析并取得了满意的效
Mounting and dismounting of ball socketed bearings are quite difficult.
转炉耳轴轴承维修、更换极为困难,因而目前很多钢厂采用剖分轴承作为转炉用耳轴轴承以简化轴承更换维修程序。
The fractured surface of bearing core shaft of a certain water pump assembly was investigated by means of macroscopic,microscopic and section fractography.
通过对水泵总成中发生断裂的轴承芯轴进行断口的宏观分析、微观分析和剖面分析,及其中各组件的相对位置、表面痕迹和宏观形貌的分析和讨论,分析失效原因,提出改进建议。
One of the main reasons of the failure on main shaft bearing of aviation engine is the damage of cage.
发动机主轴轴承失效的主要形式之一就是保持架的损坏,而保持架损坏的原因主要是保持架的磨损及滚动体对保持架的冲击。
The aviation main shaft bearing usually works under the condition of high speed and high temperature.
发动机主轴轴承常常在高速条件和高温环境下工作。
The main shaft bearings of aircraft engine are key parts of plane, its reliability and life affect directly on the reliability and life of engine and even whole plane.
航空发动机主轴轴承是飞机关键部件的关键零件，其可靠性和寿命直接关系着发动机乃至飞机的可靠性和寿命。
Bearing seizure of axial suspending bearing often occurs because of different work environment.
铁道电力机车牵引电动机抱轴式悬挂是指牵引电动机一侧通过抱轴轴承抱在机车动轮轴上,另一侧悬挂在机车转向架上的安装方式。
Research on Reliability Technology for Main Shaft Bearings of Aircraft Engine;
航空发动机主轴轴承可靠性技术研究
The Methods of Increasing the Life of the Plastic Cracker Mainshaft Bearings;
提高塑料破碎机主轴轴承寿命的措施
upper center crankshaft bearing
曲轴主轴承上中轴瓦
The feed holes for the crankshaft main bearings.
曲轴主轴承进入口。
Crankshaft and main bearings service
曲轴和主轴承的维修
Install the lower bearing inserts into the main bearing caps.
安装下轴瓦到主轴承盖。
The Model Analysis of the Ceramic Bearing Electric Spindle;
陶瓷轴承电主轴主轴的振动模态分析
Undersize crankshaft main bearing journals.
尺寸小于标准的凸轮轴主轴承轴颈。
These are the same as those used for the main bearings.
这些轴承与那些被用作主要轴承的轴承相同。
Shaft Assembly (Male, female, washer, grease….
轴组件（轴，轴套，轴承，油脂。。。）
Remove thrust bearings from rear main bearing carrier.
从后主轴承托架上拆下止推轴承。
Modeling for Rotor System of AC Magnetic Bearing Electric Spindle;
交流磁轴承支承电主轴转子系统建模
Analytical Investigation on Strength and Main Bearing Lubrication of CA4D32 Diesel Engine Crankshaft System Based on a Simulation Technique;
柴油机曲轴轴系强度和主轴承润滑仿真研究
Bearing Clearance (#1 Journal)
轴承间隙（#1轴颈）
main bearing aligning gauge
主轴承座孔同轴度检验仪
MAIN BEARING JOURNAL DIAMETER (CRANKSHAFT REMOVED)
主轴承颈部直径（曲轴已卸去）
Fatigue Life Estimation of Main Shaft Ball Bearing for High-Speed AeroEngine;
航空发动机主轴球轴承疲劳寿命估算
main drive gear bearing oil slinger
主动齿轮轴承抛油环