This paper has introduced common testing methods as well as fault handling measures by practice, these methods and measures have reference value for the testing work of meter loop.
仪表回路试验是装置开车前的联动检查,是对现场仪表的状态、特性以及计算机控制系统(如DCS、ESD、PLC等)组态功能的全面检查和确认。
Selection of connecting method in measuring-tube installation
热工仪表管路连接方式的选择
Design of Embedded Interface Based on M-BUS;
基于仪表总线的嵌入式接口设计
This paper introduces a kind of design scheme with the application of M-bus to concentrated oxygen supply data acquisition and measurement.
一种用仪表总线实现的集中供氧数据采集计量系统的设计方案,提出了集成各种消耗类表计设备及各个公司产品的方法和思路,具体实施案例表明:M-bus组成的数据采集系统可以应用于医院集中供氧数据采集计量。
In order to meet the demands of concentrated management of intellectualization,according to the communication protocol of the M-Bus,the temperature measuring & controlling system of buildings based on meter-bus is designed and implemented.
针对楼宇温度测控系统实现智能化集中管理的需要,依据M-Bus通信协议,采用TI公司的新型仪表总线专用收发芯片TSS721A及超低功耗的MSP430系列单片机,设计并实现了一种基于M-Bus的楼宇温度测控系统。
The copper brush wire is designed for flexinle connection of electrical machinery, electrical apparatus as well as instrumental ciruits.
铜电刷线是用于电机、器及仪表线路上联接用的软联接线。
High-Line Instrument Cluster Actuator Test
高压线路仪表组引动装置测试
Circuit design of FF fieldbus devices based on SIM1-2
基于SIM1-2的现场总线仪表电路设计
a circuit consisting of two branches (4 arms arranged in a diamond configuration) across which a meter is connected.
仪表可以连接到上面的由两个支路组成的线路。
INSPECT THE INSTRUMENT CLUSTER CIRCUIT BOAR
检查仪器仪表组电路板。
INSTRUMENT PANEL 22-WAY CONNECTOR
仪表板２２－路接头
linear IC tester
线性集成电路测试仪
linear multiplexing temperature tool
线性多路传输井温仪
line fault pulsing telemeter
线路故障脉冲遥测仪
INSTRUMENT PANEL 10-WAY CONNECTOR (AT BCM)
仪表板１０－路接头（在ＢＣＭ）
current circuit(of a measuring instrument)
（测量仪表的）电流电路
hot-wire instrument for measuring electrical quantities
测电量用热线式仪表
Regulation for design of tubing and wiring instrumentation
仪表配管、配线设计规定
World Factory Instrumentation Protocol;World FIPWorld FIP
总线（世界工厂仪表协议）
In the temperature control circuit of inertia typeinstrument, the optical coupler isolation power earth wire enables efficient to solve noise of the temperature controlcircuit.
在惯性仪表的温控电路中，利用光耦合器，隔离电源的地线，有效地解决了温控电路产生的干扰。
Supervise commissioning of instrumentation and final loop acceptance testing.
监管仪表调试以及仪表控制回路最终测试验收。
The Design of Field Bus Based on CAN-BUS
基于CAN总线的现场总线仪表设计
The circuits between the engine-compartment components and the instrument panel are completed through connector plugs and receptacles.
发动机总成各部件和仪表板之间的线路是通过插头和插座来连通的。