The relationship between horizontal and vertical supporting stiffness and vibrating locus of vibrating body was obtained with solving the equations and analyzing the solution of the equations.
建立惯性往复振动机械的力学模型和动力学方程,通过对动力学方程的求解及分析,获得水平支承刚度和铅垂支承刚度与振动体振动轨迹的关系;进一步分析水平支承刚度和铅垂支承刚度对振动轨迹的形状、方向和振幅的影响,提出水平支承刚度与铅垂支承刚度的设计方法,为该类机械的水平支承刚度和铅垂支承刚度的工程设计提供了理论依据。
As an optical instrument,plumb aligner is used to give a plumb line,but up to now there is no accurate concept to indicate its plumbness.
对垂准仪校准过程中同轴度和一测回垂准测量标准偏差进行了分析,并提出了铅垂p角的概念。
Design of Horizontal and Vertical Supporting Stiffness for Inertia Reciprocating Machines
惯性往复振动机械水平和铅垂支承刚度设计
A Study of the Vertical Elastic Side-bearing's Vertical Stiffness
车辆弹性旁承垂向刚度分析方法研究
In a continuous beam the vertical deflexions at the rigid supports must be zero.
在连续梁中，刚性支承处的垂直变形必须为零。
Optimization Design of Active Magnetic Bearing Stiffness Based on ANSYS
基于ANSYS的电磁轴承支承刚度优化
The stiffness of the elements in this case would be that of a supporting pier or elastomeric bearing pad or a combination of these.
诸单元的刚度则是指支承墩的刚度或弹性支承垫板的刚度或这些的合成的刚度。
Simulation Analysis on Effects of Horizontal Stiffness in Lead-Rubber Bearings
铅芯橡胶隔震支座水平刚度影响因素数值分析
The stiffness analysis on bearing of cast-in-situ concrete hollow slab that formed by edge supporting
边支承现浇混凝土空心板支座刚度分析
The Research on Bearing Spacing and Bearing Stiffness of Urban Rail Transit;
城市轨道交通钢轨支承间距与支承刚度相互关系的研究
Flexural Stiffness and Bending Capacity of Simply-supported Composite Slim Beam with Deep Deck;
简支深肋组合扁梁抗弯刚度和承载力研究
New supporting design and dynamical analysis on asymmetrical rigidity rotors
不对称刚度转子的新型支承设计及动力分析
Study on the Nonlinear Dynamics of a Bearing-Rotor System Having Nonlinear Bearing Stiffness;
具有非线性支承刚度的轴承—转子系统非线性动力学研究
Stiffness of Supporting Bearing of Output Shaft on Dynamic Performance of Three-ring Transmission
输出轴支承轴承刚度对三环减速机动态性能的影响分析
By changing these parameters and the Z-directional stiffness of the outer-ring, the stiffness and the damping characteristic of the damper can be varied.
在转子系统支承中引入摩擦阻尼器能够降低支承刚度，从而降低系统的临界转速，避开工作转速。
The method of load distribution of bottom bracing is adopted to change support rigidity,so that the bush vibration is reduced.
采用底脚载荷分配的方法改变了支承刚度 ,从而降低了轴瓦振动。
Design and Calculate Structure for the Elastic Support Variable Stiffness Apparatus of the Natural Modulation Vibration Table;
振动台固频调谐的弹性支承变刚度装置结构设计计算
Identification of angular stiffness of joint for rectangular plates with one-edge elastic supporting and three-edge free
一边弹性支承三边自由矩形板对接处角刚度的识别
Coupling Stiffness and Strength Analysis for Tubular Pump Hydropower Station Concrete Foundation and Hydroturbine Abutment
贯流水电站混凝土基础与水轮机支承座耦合刚强度分析
Mechanism of automatic suppression of the primary resonant of rotor by double balls balancer(Linear support stiffness)
双滚珠自动抑制转子主共振的机理(线性支承刚度)