On electron microscopy study of special planar defects in Al-Ni-Rh complex alloys;
Al-Ni-Rh复杂合金相中特殊面缺陷的电子显微学研究
Artificial neural network detecting method for cast products surface defects based on machine vision;
基于机器视觉的铸件表面缺陷人工神经网络检测方法
Study for the detection surface defects of the model by scanning with planar CCD array;
CCD扫描法检测模具表面缺陷的研究
HDDR NdFeB Magnet powder surface defects and their causes;
HDDR NdFeB磁粉的表面缺陷与成因
Ductile tearing assessment of surface flaw in circumferential weld of pipe-line based on J integral parameter;
基于J参量的管道环焊缝表面缺陷塑性撕裂评定
Study of surface flaw on PAN-based carbon fiber by SEM;
用SEM研究PAN基碳纤维的表面缺陷
Analysis of eddy current detector used for testing surface flaw of steel ball;
钢球表面缺陷涡流探伤仪分析
Enhancement of an ultrasonic B scan image of planar defect;
面状缺陷超声B扫描检测图像增强研究
Characteristic and recognition of ultrasonic TOFD signal and image for planar defect;
面状缺陷超声TOFD法信号和图像的特征与识别
Compared with core glass,the effect of optical processing quality of cladding glass on interface defects was more evident when its viscosity at drawing temperature was higher tha.
研究表明良好的预制棒加工质量可有效改善光纤纤芯与包层的界面状态,并且相对于纤芯玻璃来说,粘度较高的包层玻璃其加工质量对界面缺陷的影响更为显著。
Surface defect terms
GB/T15757-1995表面缺陷术语
Ingot defects may be broadly classified into internal flaws and surface flaws. Internal flaws are caused by shrinkage.
钢锭缺陷广义上可分为内部缺陷和表面缺陷。内部缺陷是因收缩引起的。
Inspect for cosmetic acceptability per cosmetic defect inspection procedure.
依照表面缺陷检验程序做表面检验
Veneer Overlaying Technology and Precautionary Measures against Relevant Defects
薄木贴面工艺及贴面缺陷的预防措施
Surface discontinuities of fasteners on nuts for general requirements
GB/T5779.2-1986紧固件表面缺陷--螺母--一般要求
Research on the Methods of Recognition Based on Disfigurement of Zonal Steel Surface;
带钢表面缺陷智能化辨识方法的研究
Design and Research of Recognition System on Railway Surface Defects;
钢轨表面缺陷识别系统的设计与研究
defect tetrahedral phase
有缺陷的四面体晶相
unclean surface
不洁的[有缺陷的]表面
Research for Relationship between Steel Defects and Slabs Defects
带钢表面翘皮缺陷与板坯缺陷对应性关系研究
The Defects of 3PE Coating by Multi-analysis (4): Material Defects
全面分析管道三层PE防腐层缺陷(四):原材料缺陷
The Flaw of 3PE Coating by Multi-analysis (1): the Coating Warping Flaw End of Steel Pipe
全面分析管道三层PE防腐层缺陷(一):翘边缺陷
It only shows her being deficient in something herself-sense or feeling.
那只不过说明了她本身有什么缺陷，不是见识方面有缺陷，就是感觉方面有缺陷。
Software Algorithms for the Determination of Metal Loss Dimensions and Subsections Generation in the Pipeline Assessment with Volumetric Type Flaw
含体积型缺陷管道的缺陷尺寸确定及子截面划分软件实现算法
The Flaw of 3PE Coating by Multi-analysis (2): the Flaw of Weld Coating
全面分析管道三层PE防腐层缺陷(二):焊缝防腐层缺陷
The Defects of 3PE Coating by Multi-Analysis (3): Apparent Defects
全面分析管道三层PE防腐层缺陷(三):表观质量缺陷
Slip- A defect pattern of small ridges found on the surface of the wafer.
划伤-晶圆片表面上的小皱造成的缺陷。
Mound- A raised defect on the surface of a wafer measuring more than0.25 mm.
堆垛-晶圆片表面超过0.25毫米的缺陷。