The variation of cut width was caused by the linear velocity difference between the top and bottom bands in RC4 cutter.
通过计算和实验发现,RC4切丝机切丝宽度的计算公式中修正系数K取值过大,造成实际切丝宽度偏小,偏离设计值约8%。
Study on problems in the designing of movable corn stalk slivering machine;
移动式玉米秸秆切丝机设计中几个问题的研究
Fieldbus based on control system design of stem cutter;
基于现场总线的切梗丝机控制系统设计
Failed in knife feeding in SQ35 tobacco cutter is a frequent failure caused by damaged primary and secondary worm gear pair resulted from over-wide clearance between tension roller and its shaft or serious wear of tension roller\'s sliding bearing.
SQ35切丝机在生产过程中经常出现刀辊不进刀故障,原因在于压链轮与轴的间隙过大,压链轮中的滑动轴承内圈孔径磨损严重,导致1、2级涡轮蜗杆出现胶合、滚压变形、折断等现象。
Develop for SQ3A Series Tobacco Cutter Drum System;
SQ3A系列烟草切丝机刀辊系统的研制
Design for SQ3A Series Tobacco Cutter;
SQ3A系列烟草切丝机的设计与应用
Constant Tension Mechanism for HS-WEDM with Compound Wire-moving Mode
快走丝线切割机床恒张力复合运丝机构研究
The Research and Development of the Wire-feeding System for the WEDM-LS;
慢走丝线切割机床走丝系统的研究与开发
Research of Wire-Feeding System for WEDM-LS;
慢走丝电火花线切割机床走丝系统的研究
Constant Speed and Tension Control of Wire Electrode for LS-WEDM;
低速走丝线切割机床电极丝恒速恒张力控制
Vibration Analysis of the Wire Electrode in HS-WEDM
往复走丝线切割机床电极丝的振动分析
Failure Judgment and Disposal Methods of Breaking Electrode Wire in Numerical Control Low Speed Wire Cutting Machine
低速走丝线切割机床断丝故障及处理方法
The food processor can shred all kinds of vegetables.
这架食品加工机可将各种蔬菜切丝切条。
Application of FIKUS WEDM Machine in Low-Speed Wire Cutting Program
FIKUS线切割机在慢走丝线切割编程中的应用
Discuss on Multi-Times Cutting Technology of Move Back and Forth Run-Wire WEDM
往复走丝电火花线切割机床多次切割技术探讨
NC slow-feeding wire-cut EDM machine
数控慢速走丝线切割电火花机床
The Research on CAD/CAM for High-speed Wire Electro-Discharge Machine;
高速走丝电火花线切割机CAD/CAM研究
Hybrid Machining Mechanism of Roll-Indent-Chipping in Multi-wire Sawing Process
多丝切割的“滚-刻-削”混合加工机理
wire drawing,drawbench and steel wire
拉丝、拉丝机、钢丝
Design and Simulation of the Wire Drive Mechanism on WEDM-LS
低速电火花线切割机走丝机构的设计与仿真
Research of Motion Control System for LS-WEDM Machine;
慢速走丝线切割机床运动控制系统的研究
The Development of Discharge Gap Control System for Wire Electrical Discharge Machining with Slow-Travelling Speed;
慢走丝电火花线切割机间隙控制系统的研究