Effect of alloying elements on microstructure and property of AgCuZnSn brazing alloy;
合金元素对AgCuZn系钎料合金组织与性能的影响
Effect of P and rare-earth La on microstructure and property of AgCuZnSn brazing alloy;
P,稀土La对AgCuZnSn钎料合金组织与性能的影响
The melting temperature was measured by a microscale DTA analyzer and the microstructure and welding performance of the brazing alloy were studied by metallographic and SEM analysis together with X-ray energy spectrum analysis.
使用微量型DTA差热分析仪测定钎料合金的熔化温度,并通过金相观察和扫描电镜观察结合X射线能谱分析对钎料合金的组织和焊接性能进行研究。
Design of lead-free solder alloy and alloy phase diagram calculation;
无铅锡基钎料合金设计和合金相图及其计算
5Ag solder alloy and conducted under different loading waveforms at room temperature.
5Ag钎料合金进行了不同加载波形下的单轴应变循环实验。
7Cu solder alloy is selected out by comprehensive comparison.
7Cu系钎料合金为基础,添加少量的RE,研究RE添加量对合金组织、力学及物理性能的影响,以确定最佳RE添加量。
The strength property of the material and its microstructure and strength property of the joint are researched based on the SnAgCuRE solder alloy fabricated under vacuum condition.
对真空条件下制备的SnAgCuRE钎料合金的力学性能及其钎焊接头的组织与性能进行了研究。
Study on Mechanical Property and Solder ability of SnAgCu System Lead-free Solder Alloy
SnAgCu系无铅钎料合金力学性能及钎焊性能研究
Study on Soldering Procedure and Joint Properties of Down Quenching SnAgCu Solder Alloy
急冷型SnAgCu系钎料合金钎焊工艺及接头性能研究
Study on Cu-Ag-Si-Ga Series Brazing Filler Alloys with Low Vapour Pressure
Cu-Ag-Si-Ga系低蒸气压钎料合金研究
Solidified structural characteristics of rapid solidified Sn2.5Ag0.7Cu solder alloy
快速凝固Sn2.5Ag0.7Cu钎料合金凝固组织特征
Study of the Effect of CuP14 on Sn-Zn Solder Alloy System;
CuP14合金对Sn-Zn系钎料合金的性能影响研究
Aluminum Alloy Soldering Procedure Research Based on the Sn-Pb-Zn Solder;
基于Sn-Pb-Zn钎料铝合金钎焊工艺研究
A Study on the Active Brazing of AlN to W-Cu Alloy with Ag-Ti_4 Active Filler Alloy
Ag-Ti_4活性钎料钎焊AlN与W-Cu合金研究
spelter brazing alloy
铜锌基硬钎焊料合金
The Study of Low-Melting-Point Filler Metal for Al-Si-Mg Series Alloys Vacuum Brazing;
Al-Si-Mg系锻铝合金真空钎焊低熔点钎料的研究
Effect of Alloy Element Addtion on IMC at the Soldering Interface of Sn-based Binary Solders;
合金元素对二元Sn基钎料钎焊界面IMC的影响
Brazing Materials and Process of High-density Graphite to TZM Alloy;
石墨与钼合金钎焊材料与钎焊工艺的研究
The Manufacturing of Filler Metal and the Joining of TiAl Alloys;
TiAl基合金高温钎焊钎料配制及连接工艺研究
Study on Brazing of Cemented Carbide to Steel Using Cu-Based Microcrystalline Brazing Alloy Foils;
基于Cu基微晶钎料的硬质合金/钢钎焊试验研究
Brazing of IC10 superalloy with Ni-based brazing fillers using Hf and Zr as melting-point depressants
Hf与Zr为降熔元素镍基钎料对IC10合金的钎焊
Phase Constitution of Soldering Seam and Mechanical Properties of Zn Matrix Filler Metal Soldering Magnesium Alloy AZ31B Joint
Zn基钎料钎焊镁合金AZ31B接头的钎缝物相及力学性能
Brazed Interface Microanalysis of Carbon-fiber Reinforced Composite Material and Titanium Alloy by Brazing Filler Metal Containing Ti Element
含Ti钎料钎焊碳纤维复合材料与钛合金的界面微观分析
Study on the Filler Metal for AZ31B Magnesium Alloy and Property of the Joint;
AZ31B镁合金钎料及接头性能研究
Effects of Pb on Properties of Sn3.5Ag0.5Cu Alloy Solder
铅对Sn3.5Ag0.5Cu合金钎料性能的影响