Artificial neural network detecting method for cast products surface defects based on machine vision;
基于机器视觉的铸件表面缺陷人工神经网络检测方法
Study for the detection surface defects of the model by scanning with planar CCD array;
CCD扫描法检测模具表面缺陷的研究
HDDR NdFeB Magnet powder surface defects and their causes;
HDDR NdFeB磁粉的表面缺陷与成因
Ductile tearing assessment of surface flaw in circumferential weld of pipe-line based on J integral parameter;
基于J参量的管道环焊缝表面缺陷塑性撕裂评定
Study of surface flaw on PAN-based carbon fiber by SEM;
用SEM研究PAN基碳纤维的表面缺陷
Analysis of eddy current detector used for testing surface flaw of steel ball;
钢球表面缺陷涡流探伤仪分析
Reason of the generation of the punching surface disfigurements of automobile back upright column outer board and the preventing measures;
后立柱外板表面缺陷的产生原因及预防措施
The detection theory of parts surface disfigurement based on the embed image processing system is introduced.
介绍了嵌入式图像处理系统用于零件表面缺陷检测的原理。
Research on surface defects of galvanized IF steel sheet;
IF钢合金化热镀锌钢带表面缺陷的研究
An Analysis on Surface Defect of 1Cr11Ni2W2MoV Steel for Compressor' Blade;
1Cr11Ni2W2MoV压缩机叶片表面缺陷分析
Study on the surface defect of WC anvil by dye penetration inspection;
着色渗透法检测硬质合金顶锤表面缺陷的可行性研究
Surface defect terms
GB/T15757-1995表面缺陷术语
Inspect for cosmetic acceptability per cosmetic defect inspection procedure.
依照表面缺陷检验程序做表面检验
Ingot defects may be broadly classified into internal flaws and surface flaws. Internal flaws are caused by shrinkage.
钢锭缺陷广义上可分为内部缺陷和表面缺陷。内部缺陷是因收缩引起的。
Surface discontinuities of fasteners on nuts for general requirements
GB/T5779.2-1986紧固件表面缺陷--螺母--一般要求
Research on the Methods of Recognition Based on Disfigurement of Zonal Steel Surface;
带钢表面缺陷智能化辨识方法的研究
Design and Research of Recognition System on Railway Surface Defects;
钢轨表面缺陷识别系统的设计与研究
Research on Control System of Inspecting Instrument for Steel Ball Surface Defect
钢球表面缺陷检测仪控制系统的研究
The Analysis for the Surface Defect of the SAE10B08 Pickled Hot-rolled Wire Rod
SAE10B08钢酸洗线材表面缺陷分析
Coating surface defect on hot-dip galvanized steel sheet and its preventive measures
热镀锌板镀层表面缺陷及其消除措施
CONTROL OF SURFACE DEFECTS IN HgCdTe FILM GROWN BY LIQUID PHASE EPITAXY
HgCdTe液相外延薄膜表面缺陷的控制
Determination of Surface Defects of Green Orange Based on Computer Vision
绿橙表面缺陷的计算机视觉分级技术
Defect Detection of Empty Bottle Surface Based on Machine-Vision
基于机器视觉的玻璃瓶表面缺陷检测
Subsurface Damage Structure and Eliminating
减少光学元件亚表面缺陷的方法研究
Analysis of surface defect on H68 copper alloy strip
H68铜合金带材表面缺陷成因分析
unclean surface
不洁的[有缺陷的]表面
Research for Relationship between Steel Defects and Slabs Defects
带钢表面翘皮缺陷与板坯缺陷对应性关系研究
Slip- A defect pattern of small ridges found on the surface of the wafer.
划伤-晶圆片表面上的小皱造成的缺陷。
Mound- A raised defect on the surface of a wafer measuring more than0.25 mm.
堆垛-晶圆片表面超过0.25毫米的缺陷。