After the Kongdong reservoir water hole plate gate rebuild into a cone valve,the stilling basin,model test was conducted.
对崆峒水库输水洞平板闸门改建为锥形阀后的消力池进行了模型试验研究。
The working principle of taper valve is analyzed originally.
提出一种适应高频工作状态的压电薄膜泵结构，初步分析了所采用的锥形阀的工作原理与作用，设计了试验泵结构，加工了样机，通过试验证明了锥形阀的有效性，为进一步的研究打下了基础。
Introduction was made the design of malfunction control circuit based on new simulation software PineCAD which was aimed at circulation fluid bed generator-set normally existing over-moment and carbonization easy to take place at the bottom taper valve.
介绍了针对循环流化床机组普遍存在的床底锥形阀容易发生过力矩以及结焦故障的现象,设计了基于新型组态软件PineCAD的防故障控制线路。
Fluid control one-way valve used cone disc, sealed a good performance.
液控单向阀采用锥形阀芯，因此密封性能好。
The taper stem head then transfers a vertical closing force to a lateral force which positively seats the knife against the seat face.
然后锥形阀杆头将垂直关闭力转换成侧向力，将闸刀放置到阀座表面上。
Non-lubricated, tapered plug assures tight seal with low breakout torque. Constructed of hardened materials with optional hard facing.
无润滑，锥形阀塞确保紧密密封，并且具有很低的启动扭矩。有硬化材料构造而成，配置备选硬面。
Numerical Simulation for Flow Field of Conical Wing Valve Based on Fluent
基于Fluent的锥形节流阀流场数值模拟
Optional disc configuration which provides line contact between spherical disc and conical body seat.
备选阀瓣结构，在球形阀瓣和锥体阀座之间具有线接触作用。
The Optimization and Experimental Research of Valveless Piezoelectric Pump with Changeable Nozzle/diffuser Elements;
连续可变锥角的锥形流管无阀压电泵的优化与实验研究
The opposite end is tapered to a small opening that is threaded to accommodate the installation of a valve.
另一端是锥形开口，车有螺纹，以便安装阀门。
The valve realizes discharging using trimming moment.
锥形锁风阀利用力矩平衡的方法实现卸灰。
A tube is a pipe tapered at both ends. Each end is threaded to allow the installation of valves, connections, or relief devices.
管道两端是锥形。每一端都车有螺纹，以安装阀门、接头或减压装置。
special taper thread tap for gas cylinder
气瓶专用锥形螺纹丝锥
If a means of sealing the shell tapping is provided, it shall be suitable for the full pressure/ temperature rating of the valve.
如果提供了用于密封筒形丝锥的工具，这个工序必须适用于阀门所有压力/度等级。
CFD Study for the Flow Filed Inside the Hydraulic Poppet Valve Considering of the Movement of Cone;
阀芯运动过程液压锥阀内部流场的CFD计算
Analysis on Flow Force of the Hydraulic Poppet Valve with the Moving Cone Based on CFD;
基于CFD的液压锥阀阀芯启闭过程的液动力分析
Steady-state Fluid Force Direction of Comparative Analysis about Slip Valve and Cone Valve
关于滑阀与锥阀中稳态液动力方向的比较分析
Design of Pneumatic Gauge Head for Valve Body's Taper of Wedged Odd Gate Valve
楔式单闸板阀门阀体锥度气动测头的设计
Study on Weakening for Cone-valve Typed One-way Valve Based on Its Structural Parameter Optimization
基于结构参数优化的锥阀式单向阀消振研究
conical thin-layer chromatography
锥形薄层色谱(法)
conical bellows
圆锥形(伸缩)风箱