Through analyzing the comprehensive inspections of the failure bearing,it is determined that undertaking early failure is caused by bearing ever-large axial load during working.
通过对故障轴承的综合检测及对检测结果的分析,确定该轴承工作过程中承受了过大的轴向负荷,是造成轴承早期失效的原因。
Objective To evaluate the effects of axially loaded MR imaging on the lumbar spinal canal,and its clinical value.
【目的】评估仰卧位轴向负荷腰椎MRI检查对椎管的影响及其临床意义。
ResultEach intervertebral angle in conventional CT scanning and in axially loaded CT scanning was as follows: L1/2 0.
目的通过采用腰椎轴向负荷压力装置,比较健康志愿者腰椎常规CT扫描与轴向负荷CT扫描所得图像中椎体间成角及椎间盘高度的差别,探讨轴向负荷CT扫描的作用,并分析其在腰椎间盘突出症CT诊断中的应用。
Through a lot of experiments and analysis, it was pointed out that the twist number of steel wire in torsion test decreased gradually with increasing axial tension load.
本文通过大量的试验和分析,得出钢丝扭转试验时,随着轴向拉力负荷的增加,其扭转次数趋于递减的变化过程。
Metal - Axial load fatigue testing???
金属－－轴向负荷疲劳试验
Most Bearings support rotating shafts against either transverse (radial) or thrust (axial) loads.
大多数轴承都支承径向或轴向负荷的转轴。
Manufacture of the axial loading device and its application in the diagnosis of lumbar spinal stenosis with CT
轴向负荷装置的制作及其在腰椎管狭窄CT诊断中的应用
"Rotary fulcrum bearings are large-sized bearings which can be subjected to combined axial, radial loads and tipping moment."
回转支承是一种能够承受综合负荷的大型支承,可同时承受较大的轴向负荷,径向负荷和倾翻力矩。
Ex Vivo Comparative Study on Lumbar Spine Disc Height and Curvature between Axially-loaded MSCT and Conventional MSCT Scanning
腰椎轴向负荷CT扫描与常规CT扫描椎体间成角及椎间隙高度的对比性试验研究
About Every Roller Load Method of Calculation In Centripetal Rolling Bearing;
向心滚动轴承中各滚动体负荷的计算方法
CQ6132W Infinitely variable speeds, power-driven feed in longitudinal and cross directions, Safety interlock, a overload safety device.
CQ6132W主轴无级变速，纵横向机动走刀，安全互锁，超负荷保险。
Principles and Optimization of the Load Balance for Multiple DC Motors on the Same Shaft
多电机同轴负荷平衡控制原理及优化
Experimental investigation on the span loading in compound lean compressor cascades with slots air injection
高负荷缝隙弯曲扩压叶栅展向负荷实验
The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.
为了避免划伤，轴承上的最大负荷应该总是小于其卸载负荷。
The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing and brineling.
为了避免划伤和压坑，轴承上的最大负荷应该总是小于其卸载负荷。
Research on stress comparison of bearings of hollowed cylindrical rollers with or without pre-loading
预负荷和无预负荷空心圆柱滚子轴承应力比较研究
Deep groove ball bearings mainly take radial load as well as take moderate axial load.
深沟球轴承主要承受径向载荷，也可承受一定量的轴向载荷。
Axial load-deformation curve and preload on angular con act ball bearings
角接触球轴承的轴向载荷—变形曲线和预紧
Numerical investigation on interaction of axial and lateral response for super-long pile
轴-横向荷载作用下超长桩数值模拟
Load test for shaft generator and its function test on sea trial.
轴带发电机负荷试验和航行时效用试验。
Exploration on Maximum Loading Design Techniques for Fan and Axial-Flow Compressor;
风扇/轴流压气机最大负荷设计技术探索
Numerical design optimization of a high-loaded low-speed axial-flow fan and experimental research
高负荷低速轴流风扇数值优化设计与实验研究