The calculation formulas of the bearing force of the turning arm are derived and the curves of the bearing force of the drive turning arm are also drawn to provide the theoretical basis for the design of this type of reducer.
本文论述了三轴式内齿行星减速器的传动原理、动力学分析，推导出转臂轴承作用力的计算公式。
Different centering model with relevant stiffness is calculated to get the bearing reaction.
对不同的校中模型,分别取不同的刚度,计算出各自的轴承反力,通过大量的计算与分析,得出了有意义的结论,可以用来指导船舶轴系的设计与计算。
The bearing reactions are calculated with different supporting stiffness for various models set up in the paper.
对不同的校中模型,分别取不同的刚度,计算出各自的轴承反力,从大量的计算与分析中得到的有意义结论,可以用来指导船舶轴系的设计与计算。
The calculation results show that the oil films have much influence on bearing reactions.
建立了滑动轴承油膜的有限元模型,分析了油膜对船舶轴系轴承反力的影响。
The transmission principle and dynamic analysis of the inner planetary gear reducer with three axies are described in this paper.
本文论述了三轴式内齿行星减速器的传动原理、力学分析，推导出转臂轴承作用力的计算公式。
According to the principle of resistance power and driving power being equal in amounts, the key parameter, the greatest acting force acted on the active tooths by the revolving arm ball bearing of the shock wave instrument is resulted.
根据阻力功和动力功相等的原理,推导出关键参数激波器转臂轴承对活齿的最大作用力.
Research on the Dynamics of Misaligned Rotor-bearing System with Rolling Bearing and Journal Bearing;
滚动轴承和滑动轴承联合作用下不对中转子—轴承系统的动力学研究
Nonlinear Dynamics of Weak-Controlled Rotor-Bearing System
轴承-转子系统在弱控制作用下的动力学行为
The trunnion assembly is supported by air bearings at the end of each arm and is held in position by brake shoes at each bearings.
耳轴组件的支承是每根臂末端的空气轴承，轴承上的闸瓦起定位作用。
a bearing designed to take thrusts parallel to the axis of revolution.
设计成可以利用与旋转轴平行的推力的轴承。
Dynamic Modeling and Modal Analysis of a Cantilever Plate Rotating Around a Rigid Hub
作定轴转动悬臂板的动力学建模及其动态特性分析
These are the same as those used for the main bearings.
这些轴承与那些被用作主要轴承的轴承相同。
Dynamic Analysis for Rotor-Bearing Systems of Large General Machinery
大型通用机械转子—轴承系统的动力学分析
"To minimize friction, the contacting surfaces in a Bearing may be separated by a film of oil or gas, these are also sliding Bearings ."
为了减小摩擦力,轴承内的两个接触面可以用一层油膜或气膜隔开,这类轴承称作滑动轴承。
Precise 3D Modeling of Design of Arm Shaft;
转向摇臂轴的精确三维造型设计应用
They can be pressed into the housing bore directly.Linear ball bearings are only suitable for linear motion.
直线运动球轴承只能用于直线运动，不能作为旋转运动部件的支承。
Analysis of rock-socketed pile uniaxial compressive strength and bearing capacity of pile tip at three dimensional effects
嵌岩桩单轴抗压强度和三维作用下桩端承载力
The moment of a force;the measure of a force's tendency to produce torsion and rotation about an axis, equal to the vector product of the radius vector from the axis of rotation to the point of application of the force.
转矩，力矩一种测量产生扭转和绕轴旋转趋势的力的单位，等于从旋转轴到力作用点的旋转矢量
radial Bearing and thrust Bearing
横力轴承与推力轴承
Study on a highly redundant manipulator's load absorption based on FEA
采用有限元法的一种超冗余操作臂承载能力的研究
Pressure-compensated air bearings are used on both ends of the trunnion axis.
耳轴两端各用一压力补偿空气轴承。
Design and Dynamic Analysis for Multi-Support Rotor-Bearing System Bearing Load Identification Test-Bed;
多支承转子—轴承系统轴承负荷辨识试验台设计及其动力学分析