Different centering model with relevant stiffness is calculated to get the bearing reaction.
对不同的校中模型,分别取不同的刚度,计算出各自的轴承反力,通过大量的计算与分析,得出了有意义的结论,可以用来指导船舶轴系的设计与计算。
The bearing reactions are calculated with different supporting stiffness for various models set up in the paper.
对不同的校中模型,分别取不同的刚度,计算出各自的轴承反力,从大量的计算与分析中得到的有意义结论,可以用来指导船舶轴系的设计与计算。
The calculation results show that the oil films have much influence on bearing reactions.
建立了滑动轴承油膜的有限元模型,分析了油膜对船舶轴系轴承反力的影响。
The experimental results indicate that the axial load strength of a circular tube confined concrete stub column is greater than that of a CFT column with the same parameters,while there is little difference on the ductility of the two kinds of columns.
试验结果表明,圆钢管约束高强混凝土短柱的轴压承载力高于同条件的普通钢管混凝土构件,但两种构件的延性无显著差异;随钢管中纵向应力的降低,构件的轴压承载力提高。
The experimental results indicate that the axial load strength of a steel tube confined concrete stub column is greater than that of a CFT column with the same parameters when D/t is 70, while the axial load strength of a square tube con.
试验结果表明,当D/t=70时,方钢管约束高强混凝土短柱的轴压承载力高于同条件的普通方钢管混凝土构件;而当D/t=47时,方钢管约束高强混凝土短柱的轴压承载力则低于普通方钢管混凝土构件;但两种构件的延性无显著差异。
The test results indicate that the height of separated tubes in a CTRC column affects little on the axial load strength and ductility of CTRC stub columns.
试验结果表明:圆钢管约束钢筋混凝土柱中被分隔钢管的高度对构件的轴压承载力和延性无明显影响;随钢管径厚比增大和混凝土强度的提高,构件的延性降低;随钢管屈服强度的提高,构件的轴压承载力提高,但钢管屈服强度对构件的延性无明显影响。
Analysis on axial strength of R-CFT stub column with unidirectional binding bars;
带约束拉杆矩形钢管混凝土轴压承载力分析
Investigation of Pressure Distribution of Partial Porous Aerostatic Thrust Bearing
局部多孔质气体静压止推轴承压力分布的研究
The pressure distribution was simulated with a approximate method.
采用近似方法模拟径向滑动轴承压力场分布。
pressure balanced bearing seal
压力平衡式轴承密封
Pressure-compensated air bearings are used on both ends of the trunnion axis.
耳轴两端各用一压力补偿空气轴承。
radial Bearing and thrust Bearing
横力轴承与推力轴承
Ultimate Capacity of Axially Loaded Thin-Walled Tapered Columns with Doubly Symmetric Sections
双轴对称薄壁锥形柱轴心受压的极限承载力
Compution on Pressure Distribution of Stern Bearing Liquid Film Reckoning in Inclination of Stern Shaft
计入艉轴倾角的船舶艉轴承液膜压力分布计算
The Determination of the Critical Technical Supply Pressure of the Rubber Guide Bearing of the Axial Pump
轴流泵橡胶导轴承技术供水临界压力的确定
The Influence Analysis on Precision of Press Caused by the Diameter Deviation of the Crank Supporting Neck
曲轴支承颈的轴径误差对压力机精度影响分析
The Stability Analysis of the Axially Loaded Aluminum Alloy Pipe;
铝合金圆管轴心受压稳定承载力研究
Study of Load Carrying Capacity of Cold-Formed Square Hollow Section Columns under Axial Load;
轴心受压冷弯方管柱承载力性能研究
Buckling capacity optimization of cylindrical shell with rectangle stiffeners under uniform axial compression
矩形加筋圆柱壳轴压屈曲承载力优化
Ultimate Bearing Capacity of FRP-Concrete Stub Columns under Axial Compression
FRP-混凝土轴压短柱的极限承载力研究
Effect of axial compression ratio to bearing capacity of piece with T-shaped section
轴压比对T形截面构件承载力的影响
Experimental Study on the Axial Compression Strength of CS Wall Slabs
CS墙板轴心受压承载力的试验研究
Increasing total load-carring area of thrust blok in the thrust bearing, increasing cooling area, the load-carring ability has been improved
通过增加推力轴承的推力块总承压面积，增加冷却面积，提高了推力轴承的承载能力
A Study on Characteristics of Air Static Pressure Thrust Bearing with Variable-Section Pressure Equalizing Groove
具有可变均压槽的气体静压推力轴承性能研究
Pressure and Streamline Field Simulation Analysis of Ball Mill Hydrostatic Bearings
球磨机静压轴承静态压力场及流场仿真分析