Using calculation method of magnetism circuit and finite element,some parameters of the permanent magnet synchronous generator(PMSG),such as non-load electric potential,output power,efficiency,cogging torque were calculated at different skew width and non-uniformity air-gap;the changing trend of the parameters were analyzed.
利用磁路和有限元的计算方法,计算了不同斜槽宽度、不同非均匀气隙情况下永磁同步发电机的空载电势、输出功率、电机效率、齿槽转矩等参数;分析了这些参数的变化趋势。
Proper skew width can weaken affixation torque and noise caused by tooth harmonics.
利用磁路和有限元的计算方法,计算了不同斜槽宽度、不同非均匀气隙情况下电机的空载电势、短路电流、输出功率、电机效率、齿槽转矩、电势波形正弦畸变率等参数;分析了这些参数的变化趋势;研究了产生这些区别的原因,得出了一些实用结论。
The influences of the geometric parameters of drill\'s edge preparation on the drilling force,torque and tool lifespan were analyzed based on the drilling tests,and the T-land width of edge preparation for drilling 42CrMo was optimized.
通过钻削试验,分析了钻头刃口处理几何参数对钻削轴向力、扭矩和刀具寿命的影响,对钻削加工42CrMo时的刃口处理斜面宽度进行了优化。
2(in carpentry and stonework)tool for making such edges
（木匠和石匠用的）斜角规.
The simulation result shows that the effect by the feeding angle and toe angle on the distribution of cross-rolling characteristic values along the rolling centre line in cross-rolling operation is following a certain law.
模拟结果表明，斜轧送进角和辗轧角对沿轧制中心线斜轧特征值分布形态的影响有一定的规律。
tilting position
倾斜角(转炉)，倾斜位置
bevel the edges of, to make a miter joint.
斜切边缘，使成斜角拼接。
an oblique a regular, a right, a triangular ] prism
斜正、直、三角]棱柱
an oblique [ a regular, a right, a triangular ] prism
斜[正、直、三角]棱柱
the oblique case
间接格,vi.1. 倾斜,歪斜,n.[C]1. 倾斜物;斜角;斜线,2. 【解】斜肌
mitre-sawing board
斜(接)面锯木(块)规
deflection angle
偏角;偏角;偏离角;偏斜角;偏转角;变位角;致偏角
heeling error
【航海】倾斜自差, 倾斜飞行;(铣头的)偏转角
A Chinese Italics Skew Detection Algorithm
中文斜体印刷字倾斜角度的检测算法
The angle or extent of such a deviation.
偏斜这种偏斜的角度或范围
give a sloping edge to(sth)
把（某物）切成或磨成斜边或斜角
To meet in a miter joint.
斜拼接对齐一个斜角接合
To drive(a nail or spike) at an oblique angle.
斜钉以一个倾斜的角度钉（钉子或大钉）
set at a sharp or high angle or slant.
角度大或者倾斜得厉害。
set at a low angle or slant.
角度小或者倾斜得不多。
Measured the planetary tilt in degrees.
测量地球倾斜的角度