Development of mould combining punching and injection forming for switch contact finger socket;
开关触片座冲压注射组合模设计
Influence of injection conditions on mechanical performance of polyamide-6;
不同注射条件对尼龙6力学性能的影响(英文)
The relationship between the PA molding shrinkage and the injection process conditions;
PA成型收缩率与注射工艺条件的关系
Determination of Volatile Phenol in Water by the Segment Flow Injection Analysis;
间隔流动注射法测定水中挥发酚方法概述
Ethanol Injection Treatment of Simple Clinical Study of Breast Cysts;
无水乙醇注射法治疗单纯性乳腺囊肿的临床探讨
Objective To investigate the effect of botulinum toxin A(BTA) injected into vocal cords for the treatment of adductor spasmodic dysphonia (SD) by direct lanyngoscopy.
目的 探讨双侧声带注射 A型肉毒毒素治疗内收性痉挛性发声障碍疗效。
The filling time steps were adaptively adjusted for flow calculation of injection molding;sub time steps of computing temperatures were calculated for each node according to local courant number,and the heat transfer analysis was conducted by the filled order of nodes.
在注射流动分析中,依据多个时间步长流过一个单元层的准则,自动调节流动分析的时间步长;而在温度计算时每个结点依据其Courant数采用不同的子时间步长,并且按着结点的注满顺序进行传热分析。
The adaptively implicit algorithm was applied for numerical analysis of injection molding, and the fountain effects in melt fronts were numerical approximated.
在注射流动与传热分析的中面模型采用自适应隐式控制体积法,并在熔体前沿进行泉涌效应的近似处理。
In this paper, the structural foaming injection molding of PP has been studied.
结构发泡注射成型技术是能够制得质量减轻、尺寸稳定性高、产品变形小的具有致密表皮和发泡芯部材料的技术。
Clinical study of the Yinxingye injections for treatment of cereb ral hemorrhage;
银杏叶注射液治疗脑出血的临床研究
Verification of “Polysaccharide nucleic acid fraction of Bacillus Calmette Guerin in treatment of verruca vulgaris by lesional injections” published by “Chinese Journal of New Drugs and Clinical Remedies”;
对贵刊刊登《卡介菌多糖核酸注射液皮损内注射治疗寻常疣》的验证
Polysaccharide nucleic acid fraction of Bacillus Calmette Guerin in treatment of verruca vulgaris by lesional injections;
卡介菌多糖核酸注射液皮损内注射治疗寻常疣
Clinical Observation of Surgery—Shaobei Injecting Method for 83 Cases of Circular Hemorrhoids;
外剥内扎加芍倍注射法治疗环状混合痔83例临床观察
Objective To evaluate the feasibility and effectiveness of needle and syringe exchange program among a community of injecting drug users (IDUs) on AIDS prevention.
干预区采用针具交换措施 (同伴教育员和医务人员在吸毒人群中宣传安全注射观念、提供免费针具、回收用过的注射器 ) ,对照区不采取任何干预措施 ,为期 10个月(2 0 0 2年 9月至 2 0 0 3年 6月 )。
a hypodermic injection [needle, syringe]
皮下注射 [注射针,注射器]
A hypodermic needle.
注射针皮下注射针头
irrigate or spray with or as if with a syringe.
用注射器灌溉或注射。
After injecting astragalus in the points, prepared model by hypodermic injection of scopolamine.
穴位注射黄芪注射液后,皮下注射东莨菪碱造模。
a piston syringe that is fitted with a hypodermic needle for giving injections.
带有皮下注射器针头进行注射的注射器活塞。
kenacort-A injection
康宁克通-A注射液
A hypodermic injection, syringe, or needle.
皮下注射器一次皮下注射，皮下注射器，或皮下注射的针
protective inoculation
预防接种 [注射]
jab a vein
[美俚]注射麻醉品
An intravenous injection of a narcotic.
麻醉注射静脉内的麻醉剂注射
After an injection, the child may want a bandage placed over the puncture site.
注射后，有些小儿想用绷带包住注射处。
Nucleus pulposus injection was performed, while the normal control group did not receive injection.
分别进行髓核注射,正常对照组不注射;
Study on Injection Energy Consumption in the Injection Molding Machine Experimental System;
注射机实验系统注射过程能耗的研究
NEW TECHNOLOGY OF INJECTION MOLDING:GAS-ASSISTED INJECTION MOLDING;
注射成型新工艺:气体辅助注射成型
New Injection Molding Technology--Water-Assisted Injection Molding
新型注射成型技术——水辅助注射成型
vincristine sulphate for injection
硫酸长春新碱注射液
vitalipid N adult
维他利匹特成人注射液
Penicillin was injected into the blood-stream
盘尼西林被注射入血液。