The friction and wear behavior of different copper alloys embedded bearings such as Sn-bronze,Al-bronze and Al-brass was tested under the End Friction Testing Machine,and the influence of different materials on copper alloys embedded bearing’s friction and wear behavior was studied.
在端面摩擦磨损试验机上对锡青铜、铝青铜、铝黄铜镶嵌轴承试样进行了常温下干摩擦对比实验,探讨了不同铜合金基体对镶嵌轴承摩擦磨损性能的影响。
According to the lubricating mechanism, a formulation of composite material is designed for the embedded bearings on the hydraulic generator.
根据固体润滑机理设计了水轮发电机镶嵌轴承用固体润滑剂配方 ,对不同冷却条件下的产品进行摩擦磨损性能试验、台架模拟试验 ,用扫描电镜 (SEM)对摩擦表面形貌进行分析。
Static characteristics analysis of inlaying radial sliding bearing;
镶嵌式径向滑动轴承静特性分析
Embedded Bearing Fault Diagnosis System DSP Side Design;
嵌入式轴承故障诊断系统的DSP端设计
Bearing Malfunction Diagnosing System Based on ARM and DSP;
基于ARM和DSP的嵌入式轴承故障检测系统
Design and Implementation of Linux Platform for the Embedded Bearing Detection System
嵌入式轴承检测系统中Linux平台设计与实现
Embedded Ethernet-Based Distributed Monitoring Systems for Bearing Noise Detection;
基于嵌入式以太网的轴承噪声分布式监测系统
Research on the Key Technologies of Smart Bearing Based on the Embedded Sensor;
基于嵌入式传感器的智能轴承关键技术研究
Research & Design an Embedded Metrical System of Friction Torque of Miniature Bearings;
基于嵌入式的微型轴承摩擦力矩测试系统设计
Research and Design of Embedded Control System for Active Magnetic Bearings;
主动磁力轴承的嵌入式控制系统设计与研究
Research on DSP-based Embedded Digital System of Magnetic Levitating Bearing;
基于DSP的磁悬浮轴承嵌入式数字控制系统的研究
Design of Control System for Magnetic Bearings Based on Embedded RTOS;
基于嵌入式实时操作系统的磁悬浮轴承控制系统设计
Application Research of Embedded Real-Time Operation Systems to Magnetic Bearings Control;
嵌入式实时操作系统在磁力轴承控制中的应用研究
Design on On-line Monitoring System for locomotive bearing fault based on embedded technology
基于嵌入式技术的机车轴承故障在线监测系统设计
The Research of Characteristics on the Scroll Compressor with Driving Bearing Set in Orbiting Scroll;
驱动轴承内嵌式涡旋压缩机特性研究
Design and Study of 4-axes Embedded Motion Controller;
嵌入式四轴运动控制器的设计与研究
Design and Research of Embedded Imprinter Unit Based on Shaft-less Transmission
嵌入式无轴传动凹印单元的设计研究
Replacing precision-insert main bearings without removing the crankshaft requires about 5 hours. Removing and replacing the crankshaft requires several additional hours.
不拆曲轴更换精密嵌入型主轴承,大约需要5小时,拆卸和更换轴承要额外增加几小时。
A Survey on Embedded System of Measuring Axle-Angle Based on FPGA;
基于FPGA的嵌入式通用轴角测角平台系统的研究
Design and Exploitation of Embedded Control System Used on Double-Axises Stabilization Platform;
双轴稳定平台嵌入式控制系统设计与开发
Design of CAN communication system for multi-axis embedded NC system
多轴嵌入式数控系统中的CAN通信系统设计