Rotacaster can slow down the filling velocity and calm down the molten metal.
本文通过对倾转铸造过程的模拟,指出缺陷的产生原因有金属流动速度过快、流动中热量损失过多、另有排气不畅、以及补缩不够等等因素。
A new type of wear - resistant steel 45SiMnCrMo has been prepared by interrupt normalizing using waste heat of casting.
利用铸造余热、采用中断正火的工艺研制出 ４５ ＳｉＭｎＣｒＭｏ新型耐磨材料，分析随中断正火温度的变化，材料的硬度、冲击韧性、耐磨性的变化规律，探讨性能变化的微观机理。
Difference on quality of 5083 alloy flat ingot from ordinary mould casting and low liquid level casting;
普通结晶器铸造与低液位铸造所得5083合金扁锭质量差异分析
The engendering rule of organism of liquidus casting aluminum alloy A356 at different heat preservation temperature, different heat preservation time was investigated.
研究了液相线铸造 A35 6铝合金在不同保温温度、不同保温时间下的组织形成规律。
The mechanisms of the grain nucleating and growing in Al alloys cast by liquidus casting were analysed theoretically.
对液相线铸造铝舍金形核机理和晶粒长大机制进行了理论分析，提出了液相线铸造形核机理：在小的过冷度下，大量的原子团簇瞬态发展成为晶核，形核数目多且均匀，有利于晶粒在互相抵触之前均呈球形长大。
In this paper the development and present state of the research on semi - solid mental slurry making are discussed, and a new technology-Liquidus Casting is proposed.
论述了半固态金属浆制备技术的发展与现状,提出了制浆新工艺-液相线铸造。
Analysis on Microstructure of AlSi7Cu5 Alloy Obtained by Slope-liquidus Method
AlSi7Cu5合金斜板近液相线铸造组织分析
Study on Simulation of Structures of Semi-solid Metal Slurry Made by Liquidus Casting Using Phase-field Method;
半固态合金液相线铸造组织相场模拟研究
Effect of Pouring Disturbance on Preparation of Semi-Solid AlSi9Mg Alloy by Near Liquidus Casting
浇注扰动对近液相线铸造半固态AlSi9Mg合金的影响
Casting and remelted microstructures of ZL201 alloy obtained by liquidus semi-continuous casting
ZL201合金液相线铸造与二次加热的合金组织
Effect of In-situ Al_2O_3 Particles on Microstructure of Aluminum Alloy by Near-liquidus Casting
原位Al_2O_3颗粒对近液相线铸造铝合金组织的影响
On the Microstructure and Refining Mechanism of ZL201 Alloy Prepared by Near-Liquidus Casting in Electromagnetic Field
电磁场作用中近液相线铸造ZL201合金的组织及其机理
Microstructure and Wear Properties of Al_2O_3/Al-Cu Composites by In-situ Reaction Liquids Casting Method
原位反应液相线铸造Al_2O_3/Al-Cu复合材料的组织及摩擦磨损特性研究
Microstructure of Near-liquidus Semi-continuously Casting 6061 Aluminum Alloy
工艺条件对6061铝合金近液相线铸造微观组织的影响
Al_2O_3p/Al-Cu matrix composites produced by in-situ reactive near-liquidus casting
采用原位反应近液相线铸造法制备Al_2O_3p/Al-Cu基复合材料
Effect of In-situ Al_2O_3 Particles on Reheating Microstructure of Near-liquidus Casting Al-Cu Alloy
原位Al_2O_3颗粒对近液相线铸造Al-Cu合金二次加热组织的影响
7075-TiC Particles Composite Produced by In-situ Reactive Near-liquidus Casting
原位反应近液相线铸造TiC_p/7075铝基复合材料的制备
Evolution of the Semi-Solid Microstructures of 7075 Aluminum Alloy Cast by LSC
液相线半连续铸造7075铝合金半固态组织演变
As-cast Microstructures of 356 Aluminum Alloy Cast by LSC
356铝合金液相线半连续铸造组织的研究
Study on the microstructure of Al-Mg-Si-Cu alloy semi-continuously cast near liquidus
Al-Mg-Si-Cu合金近液相线半连续铸造组织研究
Modification Practice of LPG Heating for SCR Continuous Casting-rolling Line
SCR连铸连轧生产线液化气加热改造实践
Study on Numerical Simulation of Gas-Liquid Two-Phase Flow during Mold Filling Process;
铸造充型过程气液两相流动数值模拟的研究
rather primitively operated foundries.
运转相当简单的铸造厂。
Research on Aluminum Alloy and High Chromium Cast Iron Prepared by Solid-Liquid Mixed Casting Process
固液混合铸造铝合金和高铬铸铁的研究