Design of hot runner injection mould with interconversion installation of moving half and fixed half for side cover;
侧盖热流道动定模反装注射模设计
According to the side cover structure characteristics of table model computer box, determined the progressive die and the single operation die.
根据台式电脑机箱侧盖的结构特性,确定了级进模与单工序模相结合的工艺方案。
Based on CAD/CAM module, the design steps of diecasting die for the side cover of cylinder were introduced.
基于Pro/E的CAD/CAM模块,以缸体侧盖为例介绍了压铸模的设计过程,利用Pro/E进行设计,大大缩短了产品研发周期、模具设计周期和加工周期,同时提高了产品设计的准确性,降低了产品开发和模具设计成本。
Install pitman shaft and side cover in the housing.
在机座中安装转向摇臂轴和侧盖。
Multiple Mechanisms Underlie Burst Firing in Mouse Ventral Tegmental Area Dopamine Neurons in Vitro;
小鼠腹侧盖膜区多巴胺细胞bursting不同机理的研究
The anterior peritoneum covers the superior surface of the bladder, forming a paravesical fossa on each side(9).
前侧的腹膜覆盖膀胱的前面，两侧形成膀胱旁窝。
Install the screw attaching the front of the end cap to the underside of the quarter panel.
安装连接末端端盖前侧到部分板底侧的螺丝。
A railroad freight car without sides or a roof.
平车一种没有侧板或盖板的铁路货车
Install seat cushion outboard trim cover.
安装座位衬垫外侧饰板盖。
short back and sides
ph.1. (脑后及两侧皆剪短的)盖式发型
Remove the mouthpiece cover by gently squeezing the sides of the cover and check the mouthpiece inside and outside to see that it is clean.
轻轻挤压吸口盖的两侧，移除吸口盖。检查吸口内外是否乾净。
Load the new battery with the side marked (+) facing upwards. Then, close the battery cover using the (+) or (-) screwdriver.
装进新电池,有“+”记号的一侧向上,再用（+）或（-）自螺丝起子盖上电池盖
Figure 3. Bottom side of a plastic stencil, showing undercut features to sit over board components.
塑胶底侧，有砍口，可以盖在电路板元件上。
Push to the side, and glide…… Knees together when you recover, and try to pull your foot in.
侧蹬，然后滑行，收腿时膝盖要碰上，脚尽量往里收。
Remove the screw attaching the front of the end cap to the underside of the quarter panel.
拆去连接末端端盖前面到部分板下侧的螺丝。
Bet you didn\'t think about the caudate and the ventral tegmental areas, did you?
我打赌你没有想象尾状核和腹侧被盖区，不是吗？
An electric branding iron was pressed into the bull's side.
用一个打火印的电烙铁盖在牛身的一侧。
A New Method of Improving a Diffuser with the Shroud Vane
无叶扩压器轮盖侧加装导叶的改进方法
Install bonnet side up and allow for accessibility for testing/service.
安装时要使阀盖侧面朝上，要便于测试和维修。
Research on Stamping Forming Numerical Simulation for Side Beam Internal Plate Cover of Car
轿车侧梁内板顶盖冲压成形数值模拟研究
The Calculating Approach of Satellite Coverage Area with Swinging of Payloads
载荷侧摆情况下卫星覆盖区域计算方法研究