Analysis on the influences of various molding temperatures on performance of AC-13 mixture;
不同成型温度对AC-13混合料性能影响分析
Influences of plasticizing temperature and molding temperature on mechanical properties of plasticized PVC and PVC/PNBR elastomer
塑化温度和成型温度对增塑PVC及PVC/PNBR弹性体力学性能的影响
During the process of the consolidation molding consolidation, this paper adopts three schemes to make kinds of samples, while it gives and studies the molding temperature as well as adopts the molding pressure, analyzing the relationship between the molding pressure and the molding thickness.
模塑成型的复合固化中,采用了三个方案复合出几种试样,并对试样的成型温度,成型压力的确定给予了探讨,同时分析了成型压力与成型厚度之间的关系。
Influence of Compaction Temperature on the Moisture Susceptibility of Warm Asphalt Mixture
成型温度对温拌沥青混合料水稳定性的影响
Influences of plasticizing temperature and molding temperature on mechanical properties of plasticized PVC and PVC/PNBR elastomer
塑化温度和成型温度对增塑PVC及PVC/PNBR弹性体力学性能的影响
Study and Development of Temperature Intelligent Monitor and Control System for Injecting Plastic Moulding;
注塑成型温度智能监控系统的研究与开发
Electron Beam Rapid Prototyping Temperature Adaptive Fuzzy PID Control System
电子束快速成型温度自适应模糊PID控制系统
For blow molding, melt temperatures of160° C to220° C are recommended.
吹塑成型的推荐熔化温度在160到220度之间。
Research on analytical model of blank temperature prediction for hot stamping of ultra high strength steels
超高强度钢板热成形板料温度的解析模型研究
Too hot machines means hardening of the rubber in the machine.
成型机温度过高极易造成液胶在机内过早固化。
Refer Processing Conditions section of this web site for recommended starting temperatures.
参照本网站的成型条件区作为建议的起始温度。
Heat Transfer in Injection Molding of Crystalline Plastics;
聚合物注射成型冷却过程中温度场的研究
Study of Modeling, Measurement and Control Technology about Vacuum-Forming Machine Temperature Field;
真空成型机温度场的建模、测量与控制技术研究
Research of Temperautre Control System on the Process of Nozzle Mould Pressing;
喷管模压成型过程温度控制系统的研究
Design and Implementation of a Small Intelligent Thermometer with Low-Cost and High-Precision
低成本高精度小型智能测温仪设计与实现
Numerical simulation of temperature field and experimental study on moulding processing of SMC
SMC模压成型热性能参数测定与温度场数值模拟
Effects of pore-forming material NH_4F and nitridation temperature on synthesis of 12H (AlN-polytypoid)
造孔剂NH_4F和氮化温度对合成12H(AlN-多型体)的影响
Studies on Temperature-Driven Morphogenesis Simulation of Greenhouse Melon Aerial Part
温度驱动的温室甜瓜植株地上部形态建成模型研究
Temperature Profile and Crystalline Behavior in Cooling Stage of Injection Moldings of High-Density Polyethylene;
高密度聚乙烯注塑成型冷却过程中温度分布及结晶行为的研究
Micro integrated pressure,temperature,and relative humidity sensor using adhesive bonding with SU-8
应用SU-8粘合技术的微型压力、温度和湿度集成传感器(英文)
Analysis and calculation of the modulation depth of the Michelson interferometer with wide field,chromatic compensation and thermal compensation
大视场消色差温度补偿型风成像干涉仪调制度的分析与计算