This article analyzes the reasons why an input shaft of driven reducer is broken and at the same time puts forward some measures and methods if it happens.
重点分析了煤矿带式输送机驱动减速机输入轴的断轴原因,并提出了处理办法和具体措施。
With the study on input shaft vibration characteristic of the four-ring-type cycloid reducer,the paper not only calculated the natural frequency of input shaft but also found the way to reduce vibration of the reducer.
通过对四环板针摆行星减速器输入轴振动特性分析,求出了输入轴固有频率,分析了影响减速器振动的因素及减振措施。
Cold extrusion technology for car input shaft has been analysed.
分析了汽车输入轴的冷挤压工艺,设计了冷挤压零件图,计算了冷挤压力,介绍了冷挤压模具及工艺流程,成功实现了汽车输入轴的冷挤压成形。
In the condition of uniaxial drive,the bearing force of the three inner gear ring of 3-ring reducer is same.
在单轴输入条件下,三环减速器三片内齿圈受力情况相同,通过分析单片内齿圈的受力情况,指出在受力计算时不可忽视惯性力和三片内齿圈受力情况,将有助于三环减速器的设计、使用和维护。
Micromachined dual input axis gyroscopes have made the best use of inherent functions of the microstructures and therefore can reach the lowest cost.
双输入轴微机械陀螺仪可最大限度地发挥微结构的固有功能并实现最低成本。
Specification: direction of rotation of output shaft varies with that of input shaft.
说明：当输入轴旋转方向改变，输出轴相应改变。
Excessive amount of grease applied to the input shaft splines.
涂抹过量黄油于输入轴齿槽中。
Finite Element Analysis about the Hollow Enter Shaft in the Accelerator of Wind Generator
风电增速箱空心输入轴的有限元分析
Finite Element Analysis of Hollow Input Shaft Based on Ansys 10.0
基于ansys10.0的空心输入轴有限元分析
Analysis and Countermeasures of Input Shaft Breaking for Gearbox of Mine Belt Conveyor
矿用带式输送机减速器输入轴断裂分析及对策
A gearing device that causes the output drive shaft to rotate at a slower rate than the engine input shaft.
低档使输出传动轴转速慢于引擎输入轴的齿轮装置
Modular units for machine tool construction--Multi-spindle heads--Casing and input drive shaft dimensions
GB/T3668.1-1983组合机床通用部件多轴箱箱体和输入轴尺寸
Failure Research of the Inputting Shaft for the High Speed Wire-rod Finishing Mill in Chang Gang;
长钢高速线材精轧机夹送辊输入轴断裂失效研究
The input axis of the azimuth gyro under this condition is vertical, and pendulum unit is nulled.
在这样情况下方位陀螺的输入轴是处于垂直位置，同时摆锤单元在零位。
Axle Input Operating Angle −7°
车轴输入工作角 −7°
Research on information input method of shaft parts for CAPP system
CAPP系统轴类零件信息输入方法的研究
pto bearing support
动力输出轴支持轴承
conveyer screw shaft coupling
输送机螺旋轴联轴节
The input signal of the system was filtrated through the line-shaft, and easy to be followed by the units.
由于输入信号经过总轴作用并过滤,易于单元驱动器跟踪。
Computing the input impedance of coax-fed microstrip patch antennas by the two-level discrete complex image method
采用二级离散复镜像法分析同轴馈电微带天线的输入阻抗
The feed holes for the crankshaft main bearings.
曲轴主轴承进入口。
Agricultural tractors and machinery-Power take-off drive shafts and position of power-input connection
GB/T17126-1997农业拖拉机和机械动力输出万向节传动轴和动力输入连接装置的位置
The handle inputs rotation upon the wheel, then transmitted to another shaft by the belt transmission mechanism.
加上皮带传动机构，手把输入旋转运动于转轮，用皮带传输转动另一个轴。