Die structure based on the process of forming small fillet radius is introduced,and deduced the formula according to the principle of volume invariably.
介绍形成小圆角半径的圆孔翻边模具的结构特点 ,按体积不变的原则 ,推导了计算公式 。
The courses were arc measurement been instead of elliptic arc measurement,part\'s manufacturing errors,the non-corrected gauge probe radius and the sensitivity coefficient of the arc of small central angle.
本文针对日益提高的现代制造精度,以测量圆弧为例,分别从4个方面分析了三坐标机测量圆弧过程中产生误差的原因:以椭圆弧测量代替圆弧测量引起的测量误差、零件本身制造引起的测量误差、测头半径未被修正引起的测量误差、小圆心角圆弧的敏感系数引起的测量误差,并提出了相应的解决方法,从而较大幅度地减小了测量误差,使测量值更接近真值。
Using the finite element analysis software eta-Dynaform to simulate the multi-location drawing process of the thick-plate cover with small fillet.
运用有限元分析软件eta-Dynaform对厚板小圆角端盖进行多工序成形过程模拟。
A Study of Burr Fillister Sizes as well as the Minimum Fillet Radius of a Final Forging Die with the Finite Element Method
毛边槽尺寸与终锻模最小圆角半径的有限元法研究
Rounded-entry driveway. Corner radius can be specified.
入口为圆角的车道。可指定拐角的半径。
DETERMING THE MINIMAL RADIUS OF BASE CIRCLE OF A CAM WITH TRANSLETINGA POINT FOLLOWER ACCORING TO THE ALLOWABLE PRESSURE ANGLE[α]
按许用压力角(α)确定直动从动件盘形凸轮机构凸轮最小基圆半径
Indexable hard metal (carbide) inserts--Corner radii
GB/T2077-1987硬质合金可转位刀片圆角半径
Drag onto the page. Right-click to edit fillet radius.
拖到绘图页上。右击可编辑圆角半径。
Radii under the head of bolts and screws
GB/T3105-1982螺栓和螺钉的头下圆角半径
Roundness depends on the sharpness or radius of curvature of the edges.
浑圆度取决于边角的锐度或曲率半径。
Calculation of Pressure Angle and Minimun Average Cylinder Radius of Cylindrical Cam Mechanisms with Oscillating Roller Follower by Using Instantaneous-center Method
用瞬心法求滚子摆动从动件圆柱凸轮机构压力角和最小平均圆柱半径
The radius of curvature of the highlighted face is too small for blend to fit. Try a smaller blend radius using Info/Minimum Radius.
如果因为面的曲率半径太小而不能创建圆角，则会发生以下错误。高亮显示有问题的面。
A 8mm Wave Multimode Conical Feedhorn With Changing Flare Angles and a Step of Radius
一种8毫米波变张角、半径突变多模圆锥馈源
Two inequalities about radius of escribed circle and bisector of angle;
关于旁切圆半径和角平分线的两个不等式
Determination of transitional fillet radius for hydroformed workpiece under wall thickness constraint
以壁厚约束的内高压胀形件过渡圆角半径确定
Application of Changing the Radius to Compensate Macro Program in Contour Fillet
变半径补偿宏程序在轮廓倒圆角中的应用
double radius button head snap
双半径半圆头铆钉窝子
A radian is the angle subtended by an arc of a circle whose length is just equal to the radius.
一弧度就是长度刚好等于半径的一段圆弧所对的圆心角。
Research on Method to Confirm Minimum Radius of Circular Curve of Mountain Expressway;
山区高速公路圆曲线最小半径确定方法的研究
the unit of plane angle adopted under the System International d'Unites; equal to the angle at the center of a circle subtended by an arc equal in length to the radius (approximately 57.295 degrees).
国际单位制采用的平面角单位；长度等于半径的弧所对的圆心角。
Application of Angle Gauge on Elliptical RT for Small Diameter Welding Tubes
角度指示计在小径管焊缝椭圆透照中的应用