The results shows that melting and oxidation are the main reason of corrosion at the high temperature.
研究表明:高温熔损和高温氧化是衬套受蚀的主要原因。
The steel corrosion on MgO-SiC composites is studied in this article.
就熔融钢液对MgO-SiC复合材料的熔损进行了分析,实验后发现,熔钢对MgO-SiC复合材料有明显的熔蚀,对试验后耐火材料和钢液之间的反应层进行了X射线衍射分析、电镜和能谱分析。
The experimental results and analyses indicated that the hydrogen content of A00 melt after purification with JDN-I flux increased little with the increasing of heat preservation time, but the mechanical properties decreased sharply and the melting loss that was below 1% and far lower than that of flux A in the market increased suddenly when heat preservation time was above 100min.
在730℃温度下,用JDN I稀土熔剂对A00纯铝进行净化处理,结果表明,净化后的铝熔体氢含量随着保温时间的延长增加很小,纯铝的力学性能在保温100min后急剧降低,纯铝熔体的熔损在保温100min后,随着保温时间的增加也急剧升高,但远低于市售熔剂A,熔体熔损基本都保持在1%以下;该种熔剂对纯铝熔体最适宜的处理时间是小于100min。
The melting loss has relations with size of melting bath,oxidation film property of melting charge,melting process and melting operation,etc,during melting aluminium alloy in reflecting frunace.
反射炉熔炼铝合金时，熔损与熔池几何尺寸、熔体氧化膜性质、熔炼工艺及操作等因素有关。
The results showed that melting loss and abrasion were the main cause of tuyere failure.
对紫铜贯流式高炉风口的失效进行了分析,结果表明:熔损和磨损是高炉风口损坏的主要方式。
Study of Erosion Resistance of Cast Hot-working Die Steels in Molten Aluminum;
铸造热作模具钢耐铝热熔损性能研究
Analysis of the Splicing Loss and Polarization Properties of the PMF
保偏光纤的熔接损耗及偏振特性分析
Study on the Property of Cavitation Erosion of Nickel-based Self-fluxing Alloy Ni67
镍基自熔合金Ni67的空蚀磨损特性研究
Growth of Laser Initial Damage in Conditioned Fused Silica at 355 nm
经355nm激光预处理后熔石英的损伤增长
Wear performance of Fe-based alloy strengthened by laser cladding under high temperature
铁基合金激光熔覆层的高温磨损性能
Causes of and Solutions to Splice Loss for Optical Fiber
影响光纤熔接损耗的因素及解决方法
Microstructure and friction and wear properties of NiCrBSi laser cladding
激光熔覆NiCrBSi涂层组织及摩擦磨损性能
Low Loss Arc Fusion Splice of Photonic Crystal Fibers
光子晶体光纤的低损耗电弧熔接方案
Study on Corrosion Mechanism of Fusion Al_2O_3-ZrO_2-SiO_2 Check Brick Used in Kinescope Glass;
显像管玻璃熔窑蓄热室用熔铸AZS格子体损毁机理的研究
Microstructure and Erosive-corrosive Wear Characteristics of Induction Cladded Ni/Cr_3C_2-NiCr Coating
感应熔覆Ni基合金/碳化物熔覆层的组织与冲蚀磨损性能
Sprayed-on Self-Fusible Alloys Assure Much Longer Service Life of Expendable Parts
大幅度提高易损件寿命的喷焊自熔性合金
Study on Slurry Abrasive Characteristics of Laser Cladding Coating and Its Application
激光熔覆涂层的浆体磨损特性及其应用研究
Research on the Microstructure and Wear Resistance of the Steel Matrix Composites Produced by Electroslag Melting and Casting Technique;
电冶熔铸钢基复合材料组织及磨损性能研究
Study on Resistivity of the Throat in the Optical Glass Electric Melting Furnace;
光学玻璃电熔窑炉流液洞耐蚀损性的研究
Research on the Abrasion Liability of Ash in CFB Boilers and Numerical Simulation of Molten Incinerator;
CFB锅炉灰磨损特性研究及熔融炉数值模拟
Damage Behavior of Welded Joints with Defects on Fusion Line;
熔合线含缺陷焊接接头损伤行为的研究
Friction Wear Research of Compacted Graphite Iron with Biomimetic Enhanced Unit Processed by Laser Cladding;
激光熔敷增强单元体蠕铁摩擦磨损性能研究
The Dry Sliding Friction and Wearing Performance of Laser Cladding 3Cr2W8V Mould Steel;
激光熔覆3Cr2W8V模具钢的干滑动摩擦磨损性能