Newly developed technique of laser cutting thick metal plates;
激光切割金属厚板新技术
Research on thickness of metallic layers from pulsed eddy-current nondestructive measurements;
金属厚度的脉冲涡流无损检测研究
Through the experiment of hardware,the relationship between margins of area and the thickness of metal and the relationship between margins of area and the distance of coil and metal from the transient current induced are gained.
测试的结果和用最小二乘法拟合得到的数据曲线较好吻合,证明了采用脉冲涡流检测金属厚度的可行性。
Thickness or diameter, as of sheet metal or wire.
直径，厚度金属板的厚度或线的直径
Research on Multi-layerd Metal Thickness Testing System Based on GMR;
基于GMR的多层金属板材厚度检测系统研究
a metal sheathing of uniform thickness (such as the shield attached to an artillery piece to protect the gunners).
金属做的一种厚度均匀的罩子（如大炮上保护炮手的挡板）。
Fabrication of Thick Metal Micromesh Sieves with High Open Area Using the UV-LIGA Process
UV-LIGA技术制备大厚度高开孔率精细金属网板
Study on the Optimum Thickness of Gradient-Porous Metal Layer
金属多孔材料梯度层最佳厚度的研究
Design of monitor system for metal thickness based on lift-off intersection point
基于提离点的金属厚度监控系统设计
Effect of the Thickness of Metal on Microstructure and Strength of Metal-ceramic Crown;
金属厚度对金瓷冠微观结构和强度的影响
Construction of the formwork and preparation of the metal reinforcement for shells required particular care and accuracy because of their limited thickness.
由于壳体的厚度有限，壳体的金属能加工制备与模板建造需要特别细心与精确。
This consists for the most part in straightening up, cleaning, and, on thicker plates above 5/16 in vee-ing the edges.
主要是矫直，清选，对于厚度超过5／16 英寸的金属板，还需将焊边做成v形坡口。
Micro-resistance test method of plating thickness of platedthrough holes for printed boards
GB/T4677.2-1984印制板金属化孔镀层厚度测试方法微电阻法
Metallic materials-Reverse bend test(Sheet and strip 3mm thick or less)
GB/T235-1988金属反复弯曲试验方法(厚度等于或小于3mm薄板及带材)
Method for measuring thickness of coated layer on composite metal-The metallographic method
GB/T11250.1-1989复合金属覆层厚度的测定金相法
A coating of metal sheets or plates.
金属板的外覆金属片或金属板的外覆
The relationship between the thickness of decarbonic layer of metal spring and the temperature and time heated;
金属弹簧脱碳层厚度与受热温度和时间的关系
Variation of Thickness and Density of Metal-Grinding Disks before and after Hardening
浅析烤制前后金属磨片厚度和密度的变化
The expriment on drawing metal board was conducted, and affection of the strain ratio of width and thickness and aeolotropism index upon the forming by drawing was analyzed.
通过金属板料的拉伸试验，分析了厚向异性指数和各向异性指数对金属板料拉延变形的影响。
VSR technology used in high intensity aluminum alloy thick plates
高强度铝合金厚板振动时效工艺的研究
Numerical Simulation of Temperature Field in Hot Rolling Process of Extra-thick Plates of 2124 Aluminum Alloy
2124铝合金超厚板热轧过程温度场的数值模拟