1-3 piezoelectric composite which contains about 25 percent ceramic phase was prepared by arranging PZT fibers and casting epoxy resin.
采用排列-浇铸法制备了纤维体积分数为25%的1-3型压电纤维复合材料,计算了材料的介电常数、机电耦合系数和机械品质因数。
Perfluorosulfonated membrane was prepared through solution-casting method from perfluorosulfonated resin, which was synthesized in lab via copolymerization of tetrafluoroethylene,hexafluoropropylene and perfluoro[2-(2-fluorosulfonylethoxy) propyl vinyl ether].
采用四氟乙烯、六氟丙烯和全氟磺酰基乙烯基醚共聚合成了全氟磺酸离子交换树脂,通过溶液浇铸法将其制成全氟磺酸离子交换膜(PSAIM)。
Hydroxyapatite/polylactic-co-glycolic acid(HA/PLGA)composites are prepared by gel-casting.
采用凝胶浇铸法,将PLGA-HA凝胶与多孔HA中间层复合。
Hydroxyapatite/poly lactic-co-glycolic acid(HA/PLGA)and PLGA-HA-TiO_2 composites were prepared by gel-casting and cold pressing-solidifying,respectively.
采用添加造孔剂法制备出骨组织工程用多孔羟基磷灰石(HA)中间层,研究了造孔剂种类、含量、温度等因素对孔径、孔隙率、力学性能的影响:应用凝胶浇铸法制备出HA-PLGA复合材料,研究了其制备工艺及其弹性模量:通过冷压与固化技术制备出HA-PLGA-TiO_2复合材料,评价了该复合材料的生物相容性。
MWNTs/HA composites were in situ synthesized by wet method with the help of ultrasonic, and PLA/MWNTs/HA composite membranes were prepared by solution casting method.
采用超声辅助原位湿法合成多壁碳纳米管/羟基磷灰石纳米复合材料(MWNTs/HA),并通过溶液浇铸法制备了PLA/MWNTs/HA复合材料薄膜。
The clay-mold bunch-casting technique for casting of Han Dynasty coins
汉代平板陶范竖式浇铸法铸钱工艺的研究
Of great importance is the introduction of continuous steel pouring.
采用钢的连续浇铸法很重要。
Introduction of the Cast Method to Examine Aggregate Breaking Force
浇铸法测试钢丝绳整绳破断拉力试验方法
Standard method of torsion test for resin cast
GB/T4726-1984树脂浇铸体扭转试验方法
Test method for flexural properties of resin casting body
GB/T2570-1995树脂浇铸体弯曲性能试验方法
Test method for compressive properties of resin casting body
GB/T2569-1995树脂浇铸体压缩性能试验方法
Test method for tensile properties of resin casting body
GB/T2568-1995树脂浇铸体拉伸性能试验方法
The generals of test methods for properties of resin casting body
GB/T2567-1995树脂浇铸体性能试验方法总则
The Control Software developing of Lead ration pouring Microcomputer control System using weightlessness method
失重法铅锭定量浇铸系统软件设计
Test method for impact resistance of resin casting body
GB/T2571-1995树脂浇铸体冲击试验方法
Two Methods for Stress Test During Explosive Casting
炸药浇铸过程中应力的两种测试方法
MODEL AND ALGORITHM OF CAST PLAN WITH UNKNOWN NUMBER OF CAST FOR STEELMAKING-CONTINUOUS CASTING SCHEDULING
炼钢─连铸对于浇次数未知的最优浇次计划模型与算法
Unsaturated polyester resin--Determination of stability of casting resin in basic solution
GB/T7194-1987不饱和聚酯树脂浇铸体耐碱性测定方法
The Method for Calculating the Strength of Centrifugally Cast Fibre Composites
离心浇铸纤维复合材料的强度计算方法
Solving Problem of Cast Scheduling in Steel-making Cast with Genetic Algorithm;
基于遗传算法求解炼钢-连铸浇次排序问题
PBS/PCL Scaffold for Tissue Engineering Prepared by Solvent Casting/Particulate Leaching
溶剂浇铸-粒子沥滤法制备PBS/PCL组织工程支架
Amatols in the form of cast charges detonate more readily than TNT in the same form.
浇铸阿马托比浇铸梯恩梯较易爆炸。
Production practice on casting the round tube blank of steel 20 with round tube blank continuous caster
圆坯连铸机浇铸20钢铸坯的生产实践