Slag detachability of new slag system basic electrode;
新渣系碱性焊条脱渣性分析
Weld fume quantity and emission rate of new slag system basic electrode;
新渣系碱性焊条发尘量及发尘速率
It was discussed about the influence of the mentioned elements on the transition coefficient of basic electrode.
利用光谱分析和扫描电镜对高硬度钢质堆焊层金属进行分析 ,采用修正后的焊条药皮重量系数计算公式计算出Nb、Ti、V的过渡系数 ,讨论了上述元素在碱性焊条中过渡系数的影响因素 ,初步得出Nb、Ti、V的过渡规律。
AN INVESTIGATION ON THE GASEOUS FLUORIDE IN WELDING FUME OF BASIC ELECTRODE
碱性焊条焊接烟气中氟化物气体的研究
Teehnological Features of Non-explosive Short Circuiting Transfer Using Basic Electrodes
碱性焊条非爆炸短路过渡工艺特性的研究
Effect of Rare Earth Oxide on Usability of Basic Electrode
稀土氧化物对碱性焊条工艺性能的影响
THE FORECAST AND CONTROL OF THE AMOUNT OF DIFFUSION HYDROGEN IN THE DEPOSITED METAL OF BASIC ELECTRODES
碱性焊条熔敷金属中扩散氢的予报及控制
A STUDY OF A.C. ARC STABILITY OF LOW-HYDROGEN BASIC ELECTRODES
碱性低氢电焊条交流稳弧性试验研究
Research on Affect of Alloy Particle to Basic Electrode s Performance;
合金颗粒度对碱性电焊条性能影响研究
Effect of Welding Process on Microstructure and Properties of Surfacing Layer with D212 Welding Electrode
D212焊条堆焊工艺对堆焊层组织性能的影响
This welding line should be gouged and welded again before tightness inspection.
这条焊缝在密性检查前要碳刨、焊。
Investigation on Properties of Deposited Metals by Shielded Metal Arc Welding Process D172;
D172焊条电弧堆焊熔敷金属性能研究
Research on Feasibility of WB36 Steel Welding Process Using Domestic Welding Electrode
国产焊条焊接WB36钢的工艺可行性研究
Research on Corrosion Resistance of Overlaying Welding Layer Using A102,A132 and A302 Stainless Steel Electrode
A102、A132和A302焊条堆焊层耐蚀性研究
The technology requirements and characteristics of overlay of a refractory steel build-up welding wire are introduced.
介绍了一种热强钢堆焊焊条的堆焊工艺要求、焊层特性。
Research on Welding Technology of Alkaline Battery Current Collector and Welding Inverter Power Supply;
碱性电池负极钉焊接技术及逆变焊接电源的研究
Study on the Corrosion Resistance of Carbon Steel Welding Seam Welded by Modified Welding Rod in the Ammonium Sulfite Solution;
改性焊条焊接碳钢焊缝在亚硫酸铵介质中的耐蚀性研究
Study of the Obdurability of 20CrMnTi Cutting Picks Treated by Lye Quenching after Hard Soldering
20CrMnTi截齿齿体钎焊余热碱液淬火强韧性研究
Necessity of Post-weld Heat Treatment for Alkaline Solution Transporting Pipeline
碱液输送管道焊后热处理必要性的探讨
The Effect of the Size of Coating Components in the Performance of D600R Surfacing Electrode;
药皮组分粒径对D600R堆焊焊条性能的影响
Study on Wear Resistance of the Electrodes of Cr13 Alloy System for Valve Sealing Surface;
Cr13系阀门密封面堆焊焊条耐磨性的研究